Guides & Tips
How to Estimate Your Office Blinds Budget Without Overspending
Most office blinds budgets fail because the number was guessed from a brochure instead of built from a measurement. This guide walks through the same three-step method our estimators use in the workshop: split the quote into components, apply a per-square-meter formula, then add installation and margin for site conditions – so your office blinds budget survives the final invoice, not just the purchasing meeting.
Need a number for your tender?
Send us your window list and we reply with a component breakdown – fabric, mechanism, fitting – no guesswork.
Request a Budget EstimateTable of Contents
1. The three components of a blinds price
Every roller blind price is built from three blocks. Understand them and you can audit any quote instead of comparing total numbers that hide different scopes:
- Fabric – the screen, dimout or blackout roll. This is the largest share and is priced per square meter.
- Accessories and mechanism – the tube, brackets, pull cord or chain, and the motor with its control: remote, wall switch or smart home integration.
- Production and installation – cutting to the millimeter, hemming and sewing, assembly, on-site fitting and after-sales support.
Because MOWIN is a fabricator with its own workshop, one accountable team covers all three blocks from survey to after-sales. Our office roller blinds are cut, sewn and installed in-house, and our fabric width of up to 2.8 m means large picture windows can be covered in a single panel.
2. A budget formula for any window set
The working formula our estimators use is simple:
- Fabric = window width (m) x window height (m) x fabric rate per square meter.
- Total per window = fabric + mechanism per unit + installation per unit.
- Project = sum of all windows + one measurement visit + mobilization + margin for site conditions.
The formula shows why a per-square-meter rate alone is misleading. A quote that is cheap per square meter can still be expensive per window if the mechanism, fitting or mobilization is inflated. On the other side, a slightly higher fabric rate can be offset by wholesale blinds pricing once volume grows.
One caution from the workshop: measure height and width accurately because a 1 cm mistake on 40 windows changes the fabric area and the total. Our free survey traps these errors before they reach the budget.
3. Worked example: 40 windows at 2 x 2 m
Take a routine office floor: 40 identical windows, each 2 m wide by 2 m high, on one facade, with mid-grade blackout fabric and manual chain mechanisms. The illustrative math looks like this:
- Fabric area per window: 4 square meters. Total: 160 square meters.
- Fabric at an assumed Rp 200,000 per square meter: Rp 32,000,000.
- Mechanism at Rp 250,000 per window: Rp 10,000,000.
- Installation at Rp 150,000 per window: Rp 6,000,000.
- Survey, mobilization and margin: roughly Rp 2,000,000.
- Rough total: Rp 50,000,000, or about Rp 1,250,000 per window.
Swap in motorization and the mechanism figure rises; swap in premium dimout and the fabric figure rises. The method stays the same, which is what makes an office blinds budget defensible to a finance team. Run a real set of measurements before you trust any estimate – see how to measure roller blinds.
4. When wholesale pricing applies
Wholesale, or harga borongan, is cheaper than unit pricing once you order dozens of windows in a single project. The savings come from four predictable sources:
- Fabric roll efficiency – one fabric family means less offcut waste per panel.
- One mobilization – one survey, one delivery, one installation crew instead of several visits.
- Repeat installation patterns – technicians fit the same bracket and drop on every window.
- One accountable contact – no reseller margin stacked between factory and site.
Wholesale makes sense for whole floors, entire towers and standardized corporate fit-outs. If you are weighing the options, read our comparison of wholesale versus per-unit roller blind pricing to see where each one wins.
5. Hidden costs that blow budgets
The line items below are the ones that silently push an office blinds budget over. Flag them in the contract before signing:
- Re-measure and remakes – blinds produced from a wrong survey size can cost a second production run.
- Non-standard frames – curved glass, angled reveals and mullions need fabrication time and test fits.
- Weekend and after-hours installation – requested to avoid office disruption, and often billed at a premium rate.
- Extra hardware – side channels for blackout, motor cabling and smart controls.
- After-sales – cheap installation with no warranty becomes your maintenance budget next year.
The single best protection is to work with a single supplier who measures, produces and fits. That is why our survey is free and includes a re-measure before production: responsibility for the wrong size sits with the fabricator, not with you. When you compare suppliers for a large order, use the checklist in choosing a blinds supplier for your project.
Finally, pair the number with the right product. If heat load is part of your tender, energy-efficient blinds for offices can turn a cost line into an operational saving, and more on our range of office roller blinds is on the products page.

